eh11a regulator datasheet, cross reference, circuit and application notes in pdf EH11A SOT eh14a regulator eh16a regulator voltage regulator sot Cheap Voltage Regulators/Stabilizers, Buy Directly from China Suppliers:EH11A H11A AZH-ADJ Enjoy ✓Free Shipping Worldwide! ✓Limited Time Sale. Cheap spot cartoon, Buy Quality regulator filter directly from China spot batteries Suppliers: EH11A AZH – ADJTRE1 adjustable power supply voltage.
|Published (Last):||14 May 2006|
|PDF File Size:||9.89 Mb|
|ePub File Size:||20.1 Mb|
|Price:||Free* [*Free Regsitration Required]|
The voltage that we should read should be higher than the voltage the regulator is rated to output. This is why we do this test. If we don’t read the correct voltages, then more than likely it is a defective regulator. Unlike fixed voltage regulators, adjustable regulators can be regulated to output adjustable voltages. eb11a
How to Test a Voltage Regulator
All a user must do is calculate the output that the regulator should ovltage and perform the same test as is shown above to see whether it is good or defective. The DC voltage setting is the setting of the multimeter that has the following symbol or voltae. If the regulator isn’t receiving sufficient voltage, of course it will not be able to output its rated regulated voltage. To test the voltage going into the voltage regulator, we take a multimeter and place it in the DC voltage setting.
If we read a higher voltage, then the voltage regulator is receiving sufficient voltage to regulate down.
The ground pin is pin 2. Measuring the Output Voltage Now that this step is complete, we now read the output voltage.
The LM is a voltage regulator is rated to output 5 volts, so we should read this output. How To Test a Voltage Regulator A voltage regulator is a device that takes in an input voltage and ovltage it down to the voltage that it is rated for.
Being that a voltage regulator passes out a regulated output voltage, the only test we must do to check a voltage regulator is a voltage test. If we do not, then the voltage regulator is defective, as it does not do the job it was designed for, which is output a regulated voltage. An adjustable regulator can be tested in the same way.
To measure the output voltage, we place the same multimeter set in the DC voltage setting and now place the positive probe of the multimeter on the output pin of the regulator and the negative probe on the ground pin of the regulator. If the regulator is rated to output 5 volts, then we should read a voltage very near 5 volts coming out from its output.
The input voltage that needs to be regulated down goes into pin 1 Input. So we’ll now go through specifically how to test a voltage regulator. If the multimeter does read a voltage near its rated output voltage, the voltage regulator is functional and is good.
A voltage regulator is a device that takes in an input voltage and regulates it down to the voltage that it is rated for.
eh11a regulator datasheet & applicatoin notes – Datasheet Archive
Measuring the Input Voltage When testing the voltage of a voltage regulator, we first check the voltage from the input pin to ground. We should now read a voltage at or about the rated voltage that the regulator is designed for.
This is to make sure that voltage is, in fact, being supplied to the regulator. This is normally volts higher. And the regulated output voltage comes out from pin 3 Output. We check the voltage input into the voltage regulator and the voltage output from the regulator.
Below is the pinout of the LM voltage regulator: If we read at the input pin the voltage which we feed into the regulator and read at the output pin the output voltage which the regulator is rated for, then we know that the voltage regulator is good.
EH11A View Datasheet(PDF) – Diodes Incorporated.
We take the probes of the multimeter and place the positive probe normally the red probe on the input pin of the voltage regulator and the negative probe normally black probe on the ground pin.
Before we get into how to read the voltages with a multimeter, first we’ll go over the pinout of a voltage regulator, so that you’ll know which pins to read voltages from. As an example, we’ll use the popular voltage reuglator, the LM