and wiring for Japanese specification FX1N PLC main units. This manual covers basic hardware details for the FX1N Series Programmable Logic Controller. FX1N Hardware Manual – 三菱可编程控制器FX1N型PLC硬件手册. User’s Manual. (Data Communication). FX1S/FX1N/FX2N(C)/FX3U. Interface Modules. INDUSTRIAL AUTOMATION. MITSUBISHI ELECTRIC. MITSUBISHI.
|Country:||Sao Tome and Principe|
|Published (Last):||28 May 2005|
|PDF File Size:||19.89 Mb|
|ePub File Size:||8.69 Mb|
|Price:||Free* [*Free Regsitration Required]|
Do not remove this screw. Features table 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Top cover Direct mounting holes 4. Circuit protector or fuse? C M3 screw to secure top cover.
C M3 screw to secure board. Check the power LED is lit. E M3 screw to secure top cover. Occupied points are shown in brackets for input and outputs. Mitsubishi Electric will accept no responsibility for actual use of the product based on these illustrative examples.
Please refer to the table below. If a response time of 0. Secure top cover with M3 screw E.
Mitsubishi FX1N-24MT-DSS Manuals
Only one board can be used at any one time, do not try to stack multiple boards. If in doubt at any stage of the installation haardware an FX1N Series Programmable Controller always consult a professional electrical engineer who is qualified and trained to the local and national standards which apply to the installation site.
Always ensure that mounted units and blocks are kept as far as possible from high-voltage cables, high-voltage equipment and power equipment. Fx1b from a personal computer or other programming peripheral.
LED is lit B Check for programming error. All layouts are diagrammatic and are only intended to aid the creation of wiring diagrams. Parallel LED Eqn 1: The operators should also be familiar with documentation which is connected with the actual operation of the completed equipment. This manual provides information for the installation and use of the FX1N.
Input circuit power supply? Circuit protector or Fuse? Associated Manuals The following manuals are recomended as esential reference material for the correct operation of a FX1N series Programmable controller.
Mitsubishi FX1N-24MT-ESS/UL Manuals
Each of the symbols used will now be listed with a brief description of its meaning. Only one special function board can be used at any time.
FX0N series extension units do not have UL certification.
If the current leakage is greater than the stated value, then add Rb. Mechanical interlocks MUST be fitted to all safety critical circuits.
D, D M Program circuit error ref. Whenever any of the following symbols are encountered, its associated note must be read and understood. Upper pot, D read from VR1. Units should not be installed in areas subject to the following conditions: Remove base unit top cover. Terminals screws should be tightened to between 0. Low voltage cables should be reliably separated or insulated with regard to high voltage cabling. Never mount them to the floor or ceiling of an enclosure.
Owing to the very great variety in possible application of this equipment, you must satisfy yourself as to its suitability for your specific application.
AC Wor ld spec. Hardwxre, D M Program execution error ref.
Mitsubishi FX1NMT-ESS/UL Manuals
Remove the hradware unit top cover. Always make sure the power is turned off, before installing a special function board. Verify the program to ensure it has been written to the PLC correctly.
This manual contains text, diagrams and explanations which will guide the reader in the correct installation and operation of the FX 1N Series Programmable Controllers. The capacitor backed memory will retain programs for a maximum of 10 days, and requires 30 harxware to recharge upon power up. FX0N series extension units do not have CE certification.
E C A Special function or optional equipment board.
FX1N Hardware Manual_图文_百度文库
Grounding is recommended but if a proper ground cannot be provided, the PLC will still operate correctly without being grounded. When the products associated with this manual are used hardare a system or individually, they must be installed in a suitable enclosure.
Check the previously down loaded program works correctly. PL E xtension block? D Top cover for board.